Blog – Page 2 – Gpat India

SOP-Ball Mill

BALL MILL STANDARD OPERATING PROCEDURE 1. Open one side of vessel by opening the screw situated over the both sides of the vessel and remove the cap from vessel. 2. Pour the ingredients desired no. and size of balls into the vessel. […]

SPIROMETER SOP

December 29, 2018December 29, 2018 admin Scientific Instruments SOP SPIROMETER, Tidal Volume, Total Lung Capacity, Vital Capacity Leave a comment

SPIROMETER STANDARD OPERATING PROCEDURE 1.Fill the water by three fourth of its height. 2.Set the scale on zero 3.Fill air by mouth 4.Check the respiratory volume 5.Remove all filled water

SOP-EDDY’S HOT PLATE (ANALGESIOMETER)

December 29, 2018December 29, 2018 admin Scientific Instruments EDDY’S HOT PLATE (ANALGESIOMETER) SOP, Index of analgesia Leave a comment

ANALGESIOMETER (EDDY’S HOT PLATE) STANDARD OPERATING PROCEDURE 1.Switch on the instrument after plugging the mains cord in the mains plug. 2.Press the switch provided between the coarse & fine knobs and adjustment digital display. 3.After this green indicator starts glowing […]

SOP-ROTAROD APPARATUS

December 29, 2018December 29, 2018 admin Scientific Instruments fall of time, Rotarod Appratus SOP, rotating rod, Skeletal Muscle Relaxant Activity Measurement, Skeletal Muscle Relaxant by Rotarod Leave a comment

ROTAROD APPARATUS STANDARD OPERATING PROCEDURE 1. Weigh and number the Rat/Mice. 2. Turn on the equipment. 3. Select the appropriate speed (20-25 RPM is ideal) 4. Place the animal one by one on the rotating rod. 5. Note down the […]

SOP -Tail Flick Analgesiometer

December 29, 2018 admin Scientific Instruments cutoff period for Analgesic activity, flicking response, Nichrome wire, percentage increase in analgesic activity, SOP Tail Flick Analgesiometer, Tail Flick Analgesiometer SOP, Tail withdrawal duration, tail withdrawal latency Leave a comment

ANALGRSIOMETER (TAIL FLICK METHOD) STANDARD OPERATING PROCEDURE 1. Weigh and number the Rat/Mice. 2. Turn on the equipment. 3. Take the basal reaction time to radiant heat by placing the tip(last 1-2 cm)of the tail on the radiant heat source. […]

SOP ELECTROCONVULSIOMETER

December 29, 2018 admin Scientific Instruments corneal electrodes, ELECTROCONVULSIOMETER SOP, Stages of Convulsions Leave a comment

ELECTROCONVULSIOMETER STANDARD OPERATING PROCEDURE 1. Weigh and number the Rat/Mice. 2. Turn on the equipment. 3. Set the convulsiometer to 150mA. 4. Hold the animal properly. 5. Place the corneal electrodes on the cornea and apply the current (150mA for […]

Actophotometer SOP

December 29, 2018 admin Scholarship Alerts Antidepressant activity measurement, Electric shock, photocells, SOP of Actophotometer Leave a comment

ACTOPHOTOMETER STANDARD OPERATING PROCEDURE 1. Weigh and number the Rat/Mice. 2. Turn on the equipment. 3. Check and sure that all the photocells are working for accurate reading. 4. Place individually each Rat/ Mice in the activity cage for 10 […]

SOP Grip Strength Meter

December 29, 2018 admin Scientific Instruments Forelimb and hind limb measurement mice and rat, front paws grip, Grip Strength Meter SOP, maximal muscle strength, motor function measurement, torso horizontal Leave a comment

GRIP STRENGTH METER STANDARD OPERATING PROCEDURE The grip test is used to measure the maximal muscle strength (motor function) of forelimbs and combined forelimbs and hind limbs. Set up and use of instrument: 1. Check that the connection of the […]

DEEP FREEZE STANDARD OPERATING PROCEDURE

December 29, 2018December 29, 2018 admin Scholarship Alerts DEEP FREEZE -20 degree, DEEP FREEZE -80 degree, DEEP FREEZE SOP, SOP DEEP FREEZE Leave a comment

DEEP FREEZE STANDARD OPERATING PROCEDURE 1.Plug in the deep freezer. 2.Switch on the mains board. 3.Adjust the thermostat knob to maintain the desired temperature. 4.Open the door. 5.Keep the samples in appropriate place. 6.Close the door.

SOP-AMPOULE FILLING AND SEALING MACHINE

December 29, 2018December 29, 2018 admin Scientific Instruments ampoule, Ampoule filling & Sealing Machine SOP, center nozzle, injection pump Leave a comment

AMPOULE FILLING AND SEALING MACHINE STANDARD OPERATING PROCEDURE Put plastic tube (right hand side bottom) in liquid vessel (or solution), is to fill in empty ampoule. Adjust the solution capacity by injection frame (working capacity 10ml to 50 ml). Keep […]